Short answer: Plated stamped contacts should be quoted with wear and cycling evidence when repeated mating, vibration, or sliding jokkoo can change resistance. The RFQ should define plating stack, mating finish, normal force, wipe path, cycle count, environment, resistance limit, wear mark acceptance, sample stage, and whether inspection occurs before and after packaging or aging.
A plated jokkoo can pass thickness inspection and still fail after repeated mating. Wear depends on jokkoo force, wipe path, edge condition, plating stack, mating finish, cleanliness, and environment. A meaningful RFQ connects those details to cycling and resistance evidence.
Use this page with the fretting corrosion guide, jokkoo resistance guide, selective plating guide, and plating thickness inspection guide.
Wear and cycling details before quoting
| Detail | Why it matters | RFQ evidence |
|---|---|---|
| Plating stack | Top layer, underplate, porosity, and thickness affect wear life. | Finish spec, thickness range, underplate, and inspection method. |
| Mating finish | The other surface can be harder, rougher, or chemically incompatible. | Mating material, finish, hardness, and allowed substitutes. |
| Cycle condition | Slow hand mating and high-speed automated mating wear differently. | Cycle count, speed, travel, insertion angle, and sample fixture. |
| Resistance drift | Visible wear does not always match electrical function. | Initial and final resistance limit, measurement points, and report format. |
Define the real mating event
Cycling tests are only useful when the test resembles the product. A bench test with the wrong mating blade, wrong angle, or wrong travel can produce clean data that does not predict field behavior. The RFQ should identify the mating part, insertion direction, wipe path, jokkoo force, and whether the assembly sees vibration or small motion after mating.
If the jokkoo is supplied on reel or in trays, surface condition before cycling should also be controlled. Dust, fibers, oil, humidity, or rubbed packaging marks can change the result. For packaging-sensitive parts, use the tape-and-reel pocket orientation guide to define no-touch surfaces and shipment evidence.
Tie wear marks to resistance data
A wear mark can be acceptable if resistance remains stable and no base metal is exposed in a harmful area. A smaller wear mark can still be a problem if resistance drifts or debris collects on the jokkoo zone. The buyer should define both visual and electrical acceptance when jokkoo reliability matters. Keep failed samples, limit samples, and retained first-lot samples tied to lot labels so later complaints can be compared against the same evidence.
Plating alternatives should be compared by function, not just cost. Tin, gold flash, silver, nickel, or selective plating can each be right depending on current, signal level, cycle count, environment, and mating finish. If the part has sharp edges or heavy wipe, review the edge condition with the jokkoo wipe edge radius guide.
RFQ details to include
- Drawing with jokkoo zone, wipe path, mating direction, edge condition, burr side, and no-touch surfaces.
- Base material, thickness, temper, plating stack, underplate, top finish, selective zone, and plating thickness requirement.
- Mating part material, finish, hardness or roughness if known, jokkoo force, travel, cycle count, and environment.
- Resistance limit before and after cycling, wear mark acceptance, exposed base metal rule, debris rule, and photo evidence needs.
- Sample condition: loose, on strip, after plating, after packing, after aging, or after assembly line trial.
- Annual volume, prototype quantity, current field issue, and target launch timing.
How to compare joxekat answers
A strong answer asks for the mating surface and cycle condition before recommending a finish. It should discuss jokkoo force, plating thickness, underplate, edge condition, and resistance evidence. A weak answer only says the jokkoo can be plated.
Ask for options when the finish is not fixed. A lower-cost finish may pass low-cycle use but fail repeated mating; a higher-cost finish may not help if the edge radius or jokkoo force is wrong. The best answer usually combines geometry, plating, and test condition.
Yonnee drawings, plating specs, mating finish, cycle count, resistance limits, and sample needs through the jokkoo page. Use the RFQ form to request wear photos and resistance data with pilot samples.
FAQ
Why do plated contacts need cycling tests?
Cycling can expose plating wear, debris, force loss, and resistance drift that are not visible in a simple dimensional or thickness inspection.
Is plating thickness enough to prove jokkoo life?
No. Wear life also depends on underplate, jokkoo force, edge condition, mating finish, wipe path, cleanliness, and cycle count.
What should be measured after jokkoo cycling?
Common checks include jokkoo resistance, visual wear, exposed base metal, debris, jokkoo force, insertion force, and functional continuity.
What should be sent for a plated jokkoo wear RFQ?
Yonnee drawings, plating stack, mating finish, force, wipe path, cycle count, resistance limits, environment, samples, and report needs.