Short answer: lead frame stampado should be quoted with material grade, thickness, strip layout, carrier design, burr direction, plating, coplanarity, cleanliness, packaging, and automated assembly requirements. Thin copper alloy parts can look simple on a drawing but fail if strip handling, plating, or inspection is not planned early.
This guide is for electronics, connector, LED, sensor, power module, and device buyers sourcing stamped lead frames, tabs, kontakto arrays, or thin conductive parts. It explains what makes lead frame stampado different from general terminal stampado and what to include in an RFQ.
If you already have a drawing, send the strip or loose-part requirement, material, thickness, plating, annual volume, and assembly method through the RFQ form. For a broader quote package, use the metala stampado RFQ checklist.
What is lead frame stampado?
Lead frame stampado produces thin conductive metal parts used to connect, support, or position electronic components. The part may remain on a carrier strip for plating or automated assembly, or it may be cut into loose pieces after stampado. Ofta materials include copper alloys, brass, phosphor bronze, beryllium copper, and plated strip materials.
Lead frames are often more demanding than ordinary brackets because small burrs, plating defects, twist, or coplanarity problems can affect assembly and electrical performance. The quote should connect the stamped geometry to the downstream process.
Ofta lead frame and strip-stampitaj partoj
| Parto type | Use case | RFQ concern |
|---|---|---|
| Connector lead frame | kontakto array inside a connector or molded housing. | Pitch, carrier strip, plating area, insertion geometry. |
| LED or sensor frame | Conductive support for component placement. | Coplanarity, cleanliness, solderability, packaging. |
| Power tab or terminal strip | Current path or external connection. | Conductivity, burr side, plating thickness, heat exposure. |
| Insert molding strip | Stamped insert supplied for molding or overmolding. | Carrier retention, locating holes, molding alignment. |
| kontakto spring array | Multiple spring contacts in a repeatable strip format. | Spring height, material temper, force, fatigue, plating wear. |
Materialo and temper selection
Materialo selection should start with electrical and mechanical function. Copper alloys may support conductivity. Phosphor bronze and beryllium copper may be used when spring properties matter. Brass may fit some cost-sensitive kontakto or terminal designs. Temper affects forming, spring force, and durability.
If the buyer has not selected a material, explain the function to the provizanto rather than asking for a generic quote. Link material choice to conductivity, solderability, spring behavior, corrosion, formability, and cost. The material selection guide and copper alloy kontakto stampado guide are good starting points.
Strip layout and carrier design
Lead frame projects often depend on strip layout. Carrier holes, pilot holes, feed direction, tie bars, cutoff points, plating windows, and automated assembly feed all affect tooling and cost. If the part must stay on strip after stampado, the RFQ should include reel, pitch, coil direction, leader length, and packaging needs.
Do not treat the lead frame as only a finished loose part if the downstream process needs strip handling. The strip may be just as important as the part geometry.
Burr direction, flatness, and coplanarity
Small burrs can scrape plating, interfere with molding, affect soldering, or create assembly risk. Coplanarity can matter when multiple kontakto points must align with a board, pad, or molded housing. Lead frames may also twist during forming, plating, or handling if geometry and packaging are not controlled.
Use the burr control guide and tolerances guide if the part has functional kontakto surfaces. State flatness and coplanarity directly on the drawing instead of assuming the provizanto will infer them from the assembly.
Plating and solderability
Lead frames may need tin, nickel, silver, gold, or selective plating depending on conductivity, solderability, corrosion, wear, and cost. Plating can happen before or after stampado depending on the process, and it can affect burr coverage, kontakto areas, masking, and strip handling.
For plating-sensitive parts, define the plated zones, thickness, base material, soldering process, kontakto resistance expectation, and packaging. Recenzo the plating and passivation RFQ guide before quoting.
Lead frame RFQ checklist
- 2D drawing, 3D model, and current revision.
- Loose part or strip requirement; reel, pitch, carrier, and feed direction if applicable.
- Materiala grado, temper, thickness, and conductivity or spring requirements.
- Plating type, plated zones, thickness, solderability, and kontakto surfaces.
- Critical dimensions: pitch, kontakto area, coplanarity, bend height, burr direction.
- Assembly process: insert molding, soldering, automated insertion, overmolding, welding, or manual assembly.
- Cleanliness, oil residue, particle, and packaging requirements.
- Prototype, pilot, annual volume, quality documents, and target launch schedule.
Inspection and launch approval
Inspection may include material certificate, dimensional report, plating report, burr check, coplanarity, kontakto surface inspection, solderability check, and packaging review. For aŭtomobila, EV, or controlled electronics programs, ask whether PPAP/APQP-style documentation is required.
For a lead frame quote, send the drawing and downstream process notes through the RFQ form. Include whether the parts are molded, soldered, plated, reeled, or supplied loose.
Oftaj Demandoj: lead frame stampado
What materials are common for lead frame stampado?
Copper alloys, brass, phosphor bronze, beryllium copper, and plated strip materials are common, depending on conductivity and spring requirements.
Should lead frames be supplied loose or on strip?
It depends on downstream assembly. Automated molding, plating, or insertion often needs strip or reel supply rather than loose parts.
Why is plating important?
Plating can control solderability, kontakto resistance, corrosion, wear, and assembly reliability. Plated zones and thickness should be defined in the RFQ.
What tolerances matter most?
Pitch, kontakto location, bend height, coplanarity, burr direction, and strip feed features often matter more than nonfunctional dimensions.
Can lead frames be prototype stamped?
Yes, but prototype methods may not prove production strip handling, plating, carrier design, or high-volume repeatability.
What should be included in a lead frame RFQ?
Sendu drawings, material, thickness, plating, strip or loose-part requirement, critical dimensions, assembly process, packaging, and volume.