Short answer: Stamped electrical contacts should not be quoted only by material and plating. If continuity or low resistance matters, the RFQ should define the mated condition, тамос force, plated surface, current or voltage method, allowed resistance or voltage drop, sample stage, and whether testing happens after forming, plating, cleaning, aging, or vibration.
A stamped тамос can look acceptable and still create an unstable circuit. Burr direction, surface contamination, weak spring pressure, worn plating, oxide film, and poor mating geometry can raise тамос resistance or create intermittent continuity. The buyer should describe the electrical function before asking for unit price.
Use this page with the terminal and тамос design guide, plating thickness inspection guide, copper terminal plating guide, and grounding clip guide.
тамос test decisions to define
| Decision | Why it matters | RFQ evidence |
|---|---|---|
| Mated condition | Resistance changes with тамос area, spring force, mating part finish, and insertion depth. | Mating sample, fixture drawing, and тамос height. |
| Test method | A continuity beep is not the same as a measured milliohm or voltage drop test. | Method, current level, probe location, and pass limit. |
| Surface condition | Plating, cleaning residue, fingerprints, and oxide can change readings. | Finish report, cleaning rule, and handling control. |
| Life state | A new sample may pass while cycled or heated parts drift. | Initial, post-cycle, heat-aged, or vibration test plan. |
Start with the electrical function
A signal terminal, battery tab, grounding clip, busbar, and shielding spring do not need the same test. A low-current signal тамос may care about stable milliohm readings and fretting risk. A power тамос may care about temperature rise, weld surface, plating thickness, and тамос area. A grounding clip may need repeatable pressure against a chassis or PCB pad.
The drawing should identify the actual тамос zone. Do not let inspection probes touch an easy flat area if the circuit depends on a small coined point, spring beam, or plated edge. For related material choices, compare the battery тамос plate guide, pre-plated versus post-plated terminal guide, and thin gauge штампкунӣ guide.
Умумӣ reasons readings drift
тамос resistance can move after tooling wear changes burr height, after plating thickness shifts, after cleaning residue remains on the surface, or after spring features relax. The таъминкунанда should not treat the test as a final inspection only. It should connect to material temper, forming direction, plating route, packaging, and the handling rule for тамос surfaces.
If readings are important to the product, define whether parts are tested loose, assembled, nested in a fixture, or mated to the customer’s part. A таъминкунанда may also need a go/no-go continuity screen plus a measured resistance audit on a smaller sample size.
RFQ details to include
- Drawing, 3D model, material, thickness, temper, plating, and identified тамос zones.
- Electrical function: signal, ground, battery, busbar, shielding, solder tab, or press-fit тамос.
- Test method: continuity only, milliohm resistance, voltage drop, current level, probe points, and pass limit.
- Mating part material, finish, insertion depth, working height, and required тамос force if known.
- Test stage: after штампкунӣ, after plating, after cleaning, after assembly, after cycling, or after heat exposure.
- Packaging and no-touch rules for тамос surfaces.
How to compare таъминкунанда answers
A strong answer names the feature that carries current and explains how the process keeps that feature clean, plated, and correctly loaded. A weak answer only says the part is conductive. Ask whether the таъминкунанда can correlate electrical readings with spring force, plating thickness, and visual condition.
Ирсол кунед drawings and the electrical test requirement through the тамос page. If the test method is not final, use the RFQ form to ask for a practical inspection route, including sample quantity, fixture need, measurement equipment, and what data will be supplied with first articles.
For low-resistance contacts, also ask what will happen when a lot fails. The response should separate sorting, rework, cleaning, retesting, and engineering review. That links the test plan to the cleanliness guide and rework and sorting guide.
Саволҳо
Is continuity testing enough for stamped contacts?
Not always. Continuity only confirms an electrical path. Low-resistance or signal contacts may need measured resistance or voltage drop under a defined mated condition.
What causes high тамос resistance?
Умумӣ causes include low тамос force, oxide, contamination, plating defects, burrs on the mating surface, wrong probe location, or surface wear after cycling.
Should тамос resistance be tested before or after plating?
If plating affects the тамос zone, the important acceptance test is usually after final plating and cleaning. Early checks can still help process control.
What should be sent for a тамос test RFQ?
Ирсол кунед the drawing, material, plating, mating part, тамос zone, force target, test method, pass limit, sample stage, quantity, and packaging requirement.